• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

What became known as BIM products differed from architectural drafting tools such as AutoCAD by allowing the addition of further information (time, cost, manufacturers' details, sustainability, and maintenance information, etc.) to the building model. Will settle over time, losing some of its effectiveness. Dry-spray (but not wet-spray) cellulose can settle 20% of its original volume. Cellulose is treated with a flame retardant and insect repellent, usually boric acid and sometimes borax to resist insects and rodents. ASTM Standard C-1149 - Industry standard for self-supported spray-applied cellulose insulation for exposed or wall cavity application - covers density, R-value, surface burning, adhesive strength, smoldering combustion, fungi resistance, corrosion, moisture vapor absorption, odor, flame resistance permanency (no test exists for this characteristic), substrate deflection (for exposed application products), and air erosion (for exposed application products). An additional source of insulation derived from hemp is hempcrete, which consists of hemp hurds (shives) mixed with a lime binder.

In a fossil fuel power plant using a steam cycle for power generation, the primary heat source will be combustion of coal, oil, or natural gas. The source of heat for a boiler is combustion of any of several fuels, such as wood, coal, oil, or natural gas. These sections are assembled on site to create the finished boiler. In a cast iron sectional boiler, sometimes called a "pork chop boiler" the water is contained inside cast iron sections. However, ferritic stainless steel is often used in superheater sections that will not be exposed to boiling water, and electrically-heated stainless steel shell boilers are allowed under the European "Pressure Equipment Directive" for production of steam for sterilizers and disinfectors. Historically, copper was often used for fireboxes (particularly for steam locomotives), because of its better formability and higher thermal conductivity; however, in more recent times, the high price of copper often makes this an uneconomic choice and cheaper substitutes (such as steel) are used instead. This is the type of boiler used in nearly all steam locomotives. This type generally gives high steam production rates, but less storage capacity than the above. Fire-tube boilers usually have a comparatively low rate of steam production, but high steam storage capacity.

With one or two large flues-an early type or forerunner of fire-tube boiler. 18th century Haycock boilers generally produced and stored large volumes of very low-pressure steam, often hardly above that of the atmosphere. Although such heaters are usually termed "boilers" in some countries, their purpose is usually to produce hot water, not steam, and so they run at low pressure and try to avoid boiling. Water tube boilers can be designed to exploit any heat source and are generally preferred in high-pressure applications since the high-pressure water/steam is contained within small diameter pipes which can withstand the pressure with a thinner wall. Radiant barriers can function as a vapor barriers and serve both purposes with one product. The furnace can be situated at one end of a fire-tube which lengthens the path of the hot gases, thus augmenting the heating surface which can be further increased by making the gases reverse direction through a second parallel tube or a bundle of multiple tubes (two-pass or return flue boiler); alternatively, the gases may be taken along the sides and then beneath the boiler through flues (3-pass boiler). Heat/ Thermal Insulation is a barrier material to resist / block / reflect the heat energy (either one or more of the Conduction, Convection or Radiation) to transfer from one side to another.

Reflective insulation and radiant barriers reduce the radiation of heat to or from the surface of a material. The R-value test measures heat transfer through the material, not to or from its surface. In case of a locomotive-type boiler, a boiler barrel extends from the firebox and the hot gases pass through a bundle of fire tubes inside the barrel which greatly increases the heating surface compared to a single tube and further improves heat transfer. BIM-based knowledge transfer framework from industrialized economies to urban construction projects in developing nations, generic BIM objects can benefit from rich building information within specification parameters in product libraries, and used for efficient, streamlined design and construction. Flash tank: High-pressure blowdown enters this vessel where the steam can 'flash' safely and be used in a low-pressure system or be vented to atmosphere while the ambient pressure blowdown flows to drain. In a flash boiler, the tube is kept so hot that the water feed is quickly flashed into steam and superheated. A flash boiler differs from the type of mono-tube steam generator in which the tube is permanently filled with water. Flash boilers had some use in automobiles in the 19th century and this use continued into the early 20th century.

In the event you liked this post and also you would like to obtain more info about FireStop certified contractors i implore you to stop by our own webpage.