• 목록
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, patio doors go through wear and tear that can cause locks that fail. There are a few basic steps you can follow to ensure the security of your uPVC door.

These quick fixes can make your home safer no matter if you adjust the lock or clean the mechanism.

Clean the Lock

Patio doors are great for letting the outdoors in while keeping out the elements. However they could pose an issue for security when the lock isn't functioning properly. As time passes, wear and tear, hot and cold weather dirt and debris could affect the lock on your patio door and make it difficult to open. With a little effort, you can make sure that the lock on your patio door always works correctly.

It is important to first clean the patio door lock and all moving parts. This will help get rid of any grime or coatings that might be hindering your lock from working properly. Begin by wiping the moving parts of the lock for your patio door using a damp cloth. then use a scouring pad or rough damp cloth to scrub any difficult-to-access areas of the door or frame that are ingrained with dirt. Then wipe the lock using a dry towel to get rid of any remaining moisture. Allow it to air-dry before you use it.

If your patio door uses pin-tumbler locks, you can apply powdered Graphite on the key. You can also use a Teflon lubricant such as WD-40 Multi Use Product. This type of lubricant is able to be applied easily and will not disintegrate over time. If you're unable to locate a suitable lubricant you could try using a pencil that has an extremely sharp tip. Put the pencil into the lock and move it around to spread the graphite.

The tracks for sliding patio doors also require regular maintenance to keep them free of dirt, dust and other debris. These tracks are especially susceptible to snow and ice, which can cause them become stuck or slack which makes it difficult for your patio doors to open and casement close.

You can clean the track rails and rollers on sliding patio doors by removing any weather stripping that is damaged or dirty. Clean it and replace it. The same applies for rollers on patio door lock repairs near me doors, which can be wiped down and sprayed with a non-stick lubricant that will allow them to move freely.

Lubricate the moving parts

uPVC French Doors, like sliding patios, operate using 3 to 4, or sometimes 5 point locking mechanisms. This includes the lock cylinder and handle which is operated by keys. These doors require maintenance, the lubrication of moving parts. This can be accomplished with the use of a thin oil but not WD40. It is recommended to do it at least once a year.

If hinges that are sagging don't cause the problem, it could be that the door is not aligned. It could be rubbing against or catching the strike plate's hole in the frame. Take off the strike plate and employ a sharp tool enlarge its mortise. This will permit the latch to fit into the hole and also prevent it from hitting the frame.

Once the cylinder is cleared of the way take a measurement of its width using an object or a piece of wood that fits into the adjustment screw gap above the lock. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Verify the width of the lock.

If your patio door latch is difficult to turn, even after cleaning and lubricating, it's possible that it is out of alignment with the strike plate hole. Check to see if the door is balanced and if the hinge screws are tight however, in many instances, moving the strike plate up or down could fix the problem.

The latch might not work properly when the strike of the lock is not large enough. In this instance, you can widen the opening using an hammer and chisel. Then, test the latch to ensure it doesn't rub against the jamb frame of the door or get caught on it.

You should identify the type mortise lock that you are using before you purchase the replacement. This can be done by looking at the end faceplate and observing whether it is square or round. Then, take a look at the screw holes on the existing lock and note the size of each one. This information will allow you to locate a replacement lock that is exactly the same size and fits into your existing hole.

You'll need to locate the mortise lock and examine it for any scratches, bends or other damage that needs to be repaired. A bent or damaged latch is more likely to break than one that's been used much, so be sure to replace the lock with a brand new one that is secure in the event you notice any signs of damage or wear.

After you've determined the type of lock replacement you require It's time to begin the actual repair. Remove the handle and spindle out of your patio door, and then insert the new one. Begin by installing the handle inside, aligning it with the spindle, and then securing it in place with the two bolts or screws that secure it. Install the exterior handle following the interior handle. Once you have completed these steps, test the handles to make sure that they open and shut easily and that the latch is in contact correctly with the strikeplate.

Check the Strike of the Door.

The strike plate and door latch are two parts that work together in order to secure the door. If they are not aligned properly, the latch won't latch the door shut correctly. Fortunately, the issue is usually simple to fix.

First, examine the strike plate's holes for receiving to make sure they are free of obstructions like dirt or plastic plugs. Release the screws that hold the strike plate in place. This will allow it to move horizontally, but not separate it from the frame. Then adjust the strike plate until its receiving holes align with the latch hooks on the door latch. Once the strike plate is adjusted then tighten the screws and then test the door to see whether it locks smoothly after the new adjustment.

Door strike plates can be difficult to access for homeowners with sliding patio doors, however they are essential to lock and unlock your door. The plates made of metal are located at the top and bottom jambs of your door, where they serve as the support for the latch. The door latch is placed on the strike plate to create the seal when it is closed. If the strike plate is damaged, rusted or not installed correctly, it may stop the latch from locking the door securely.

A misalignment of the latch and strike plate is one common cause for a patio lock to not close or remain in place. This can be checked with the "lipstick" test. Apply some lipstick along the edge of the deadbolt and then cover it with masking tape. The lipstick will leave the mark when you shut the door. This will indicate exactly where the latch meets the strike plate. If the mark is too low or high, you can easily adjust the strike plate.

Locks for sliding patio doors help keep your home safe from intruders, and if they're not working correctly, you should solve the issue fast. Follow these easy steps to repair your patio door lock and restore it's function.